Infiniti Drivelines
Having Vibrations Issues with your Infiniti?
We offer Highest quality replacement drivelines for the following Infiniti models: FX35 AWD/Rear Shaft, G35 Coupe & Sedan, J30 and M30.
Infiniti driveshaft's design is intended to completely eliminate natural frequency vibrations. The problem with this design of universal joint is that repair is difficult, relatively expensive and prone to early failure. And front driveshaft run out, the most common Infiniti driveshaft design is that the front driveline is centered directly off the transmission main shaft. This design causes Infiniti driveshafts to rotate with the smallest amount of radial run-out possible. Additionally the rear part of a Infiniti driveshaft is centered with the next most accurate means, a precision piloted fit flange.
As with and high speed rotating mechanism when parts wear or fail, serious vibrations can start small and build to cause sever damage to other drivetrain related components. An updated designed universal joint is manufactured to exacting specifications, which specifically eliminates the root cause of early Infiniti u-joint/driveshaft failure.
Our state of the art manufacturing and high speed balancing facility provides driveshafts that exceed the original manufactures specifications. Our shafts also come with a new center bearing (If Used).
Replacement of the old existing driveshaft can prevent future diveshaft problems and failure bushing and seal in transmissions and differential caused by excessive vibration. Also enhancing the comfort of your Infiniti 's ride.
Below we have provided a detailed applications guide covering all Infiniti models drivelines, select your Infiniti model SFX35 AWD/Rear Shaft, G35 Coupe & Sedan, J30 and M30. Just locate your Infiniti model year and chassis model, then you will be able to see the correct part number and your cost. Just select double click the part number, this will take you to a more detailed information you can then from this page proceed to ordering replacement drive shaft and it will be on its way to you.
Complete Infiniti Drive Line and Driveshafts OEM replacement units, let us replace your existing unit and you save money. We offer a complete line of Infiniti shafts, center bearings, end yokes, u-joints, and flanges.
Additional information on other manufactures vehicle driveshafts they provide, just click below.
BMW |
Chevy/GM |
Dodge Car |
Dodge Truck |
G Series Chevy |
Honda Ridgeline |
Drivelines/Driveshafts, Rear Ends, Overdrive Units, Manual Transmissions and Transfercases, Full Service Shop |
||
Jaguar |
J10 Jeep Truck |
Jeep Cherokee |
Jeep Commander |
Jeep Grand Wagoneer |
Jeep Liberty |
KIA |
Lexus |
|
Mazda |
Mercedes |
Mercury |
Mitsubishi |
Nissan |
Subaru |
Toyota |
Need help or tips with drivelines see our free information below on how to maintain or troubleshoot driveline's and driveshafts including angle phasing issues.
30 Years Experience, we can Help!
|
Save money send us you core and we will re-builld it and high speed balance your shaft. Save 20% or more. Troubleshooting Driveline Problems: Angles and Phasing - Diagnostic & Testing Field Problem Analysis and Answers |
See our You Tube video: How we manufacture the highest quality drivelines. |
The driveshaft must operate through constantly changing relative angles between the transmission and axle. It must also be capable of changing length while transmitting torque. The axle of the vehicle is not attached directly to the frame, but rides suspended by springs in an irregular, floating motion. This means the driveshaft must be able to contact, expand and change operating angles, when going over bumps or depressions. This is accomplished through universal joints, which permit the driveline to operate at divergent angles, and slip joints, which permit contraction or expansion to take place.
We specialize in high speed balancing of the final assembled driveline's If your shaft is not balanced with the actual end yoke and U-joints, you have not fixed the potential vibration problems. Our shop features the latest in driveling manufacturing and balancing equipment.
High Speed Balancing is the secret to smooth vibration free performance!
A driveshaft will not run smooth and vibration-free unless it is straight and in balance. Our shafts are, after assembly and before welding, pre-straighten to the above specifications. We then dynamically high speed balance the entire shaft assembly at the speed representative of the speed the shaft will encounter in its normal application.
Infiniti Driveline and Driveshafts Replacements Products
Please Click on Part Number for additional information or to buy it online, you can also call toll free (800-216-1632).
Model | Part Number |
Year
|
Year
|
TransType |
Your Cost
|
FX35 AWD/Rear Shaft | DTS3192-315 |
2003
|
2008
|
Auto |
$718.90
|
G35 Coupe & Sedan | DTS3192-313 |
2003
|
2006
|
Auto |
$718.90
|
G35 Coupe & Sedan | DTS3192-314 |
2003
|
2006
|
Manual |
$718.90
|
J30 | DTS1292-301 |
1990
|
1997
|
Auto |
$759.81
|
M30 | DTS1292-300 |
1990
|
1992
|
Auto |
$615.16
|