
Having problems with your Dana 44 front differential or rear end? We offer a complete line of ring and pinion gears sets plus rear end parts for the DANA 44 differentials.
You can purchase Genuine Dana high quality Dana 44 ring and pinion sets in various ratios
We also offer high quality rear end bearing overhaul kits including pinion bearings, pinion seal, crush sleeve, pinion nut, shims, ring gear bolts, marking compound and gasket. This differential was utilized by Chrysler in their pickup line starting in 1969 and Jeep line starting in 1967 including the J10, Wagoneer, CJ5 and Cherokee. International used in the pickup line and Scout from 1966 to 1980, it is also found in some Ford applications Bronco, F-100, F150, early Thunderbirds 1955 to 1956 and the Corba 1963-1967. GM used this very popular differential in their K10 and K30 pickups from 1960 to 1990 and it was even used in their Corvette line between 1980 and 1982 see applications.
Our inventory includes OE ring gear and pinion sets, bearing rebuild kits, internal parts kit (spider and side gears), positraction repair kits (clutch plates)and OE Positractions. We are also able to supply axles, carriers, cases, both empty and loaded cases. shafts, spindels, tierods and yokes. Aftermarket Positraction units we offer include Lockrights by Powertrax, Auburn, Detroit Lockers, Trac Loc and ARB air lockers.
We are a Dana Spice volume distributor and offer a complete line or ring gear and pinions up to and including the large Dana 80 differential. Specifications are provided below to assist you in the identification and setup as well as torque spec.’s required for rebuilding your Dana 44 differential.
Along with our quality parts you have free access to applications information for available ring and pinion ratios, information to assist you in identification of the differential that you have. Free information for ring and pinion installation is provided alone with specification and carrier/case breaks when you are considering gear ratio changes. You can review applications available to assist you with selection of the specific positraction unit that you may need to improve your performance.

With this number we can tell you exactly what components the factory used in the assembly of your differential. You can also the following link below to research exactly what parts you need, following step 1 and then step 2 and then enter your bill of material number:

You get the right parts the first time! Once you know the bill of material number give us a call or down load and refer to the appropriate parts catalog listed for your bills of material number. The parts catalog contains exploded views, parts listings, bill of material tables, and variable parts tables for each series is listed below to help you identify the parts you need:
- Chevrolet X510-3DSD
- Ford X510-2CVSPGMC
- Chrysler/Dodge X510-5DSD
- Jeep / Eagle 1999-Current X510-6
- Miscellaneous models 1979-1984 X510-7DSD
- All manufacturers prior to 1978 X510-8DSD
- All manufacturers 1985-1998 1/2 X510-9
- General Information XG1.
Ring and Pinions Sets Cases, Bearing Kit and Misc Parts Positraction Units |
Purchase the parts at drivetrain.com and receive free installation technical support by telephone! Yes real technicians with many years experience, not just a salesperson. Just a phone call away 800-216-1632. |
Other Dana Differential Information
|
Click on Dana 44 Part Number to Purchase on online
DANA 44 Ring Pinions |
|||||||
2005024-5 | RING & PINION 4.10 | 2007 JK FRONT | $375.16 | ![]() |
|||
22104-5X | GEAR SET 3.92 | RING & PINION ONLY | $247.62 | ||||
22105-5X | GEAR SET 4.55 | RING & PINION ONLY | $179.22 | ||||
22106-5X | GEAR SET 3.07 | RING & PINION ONLY | $205.37 | ||||
22404-5X | GEAR SET 3.44 | RING & PINION ONLY | $340.42 | ||||
22736-5X | GEAR SER 3.73 | RING & PINION ONLY | $239.07 | ||||
22745-5X | GEAR SET 4.09 | RING & PINION ONLY | $189.18 | ||||
22856-5X | GEAR SET 3.54 | RING & PINION ONLY | $215.31 | ||||
23053-5X | GEAR SET 4,89 | RING & PINION ONLY | $188.48 | ||||
24649-5X | GEAR SET 4.09 | RING & PINION ONLY | $256.70 | ||||
706017-10X | GEAR SET KIT 4.27 | PINION BRG, SHIM & BOLTS INCL. | $284.80 | ||||
706017-11X | GEAR SET KIT 3.92 | PINION BRG, SHIM & BOLTS INCL. | $292.31 | ![]() |
|||
706017-1X | GEAR SET KIT 3.07 26 Spline | PINION BRG, SHIM & BOLTS INCL. | $254.98 | ||||
706017-21X | GEAR SET KIT 4.55 26 spline | PINION BRG, SHIM & BOLTS INCL. | $254.49 | ||||
706017-2X | GEAR SET KIT 3.31 26 Spline | PINION BRG, SHIM & BOLTS INCL. | $254.98 | ||||
706017-3X | GEAR SET KIT 3.54 26 Splines | PINION BRG, SHIM & BOLTS INCL. | $255.37 | ||||
706017-4X | GEAR SET KIT 3.73 26 Splines | PINION BRG, SHIM & BOLTS INCL. | $254.98 | ||||
706017-5X | GEAR SET KIT 4.09 26 Splines | PINION BRG, SHIM & BOLTS INCL. | $254.98 | ||||
706017-8X | GEAR SET KIT 5.38 26 Splines | PINION BRG, SHIM & BOLTS INCL. | $285.22 | ||||
706017-9X | GEAR SET 5.89 26 Splines | PINION BRG, SHIM & BOLTS INCL. | $287.05 |
Your gears run cooler and last longer!
![]() Order above high performance synthetic oil and friction additive combo kit at time of order for ring and pinion or bearing overhaul kit and pay only $49.95 plus S&H, a $54.00 value.
|
|||
707020-3X | RING & PINION KIT 3.54 | FRONT 1985-86 D-500 & D-800 | $285.81 | ||||
707020-4X | RING & PINION KIT 4.09 | $202.81 | |||||
707020-5X | RING & PINION KIT | FRONT | $377.06 | ||||
707240-9X | RING & PINION KIT 4.09 RATIO-REVERSE, 26 SPLINE PI | PINION BRG, SHIM & BOLTS INCL. | $336.30 | ||||
707283-9X | RING & PINION KIT 4.09 | $399.70 | |||||
707309-1X | RING & PINION KIT 4.10 RATIO-THICK, 26 SPLINE PINIO | NPINION BRG, SHIM & BOLTS INCL. | $244.98 | ||||
707338-1X | RING & PINION KIT 3.54 RATIO, 26 SPLINE PINION, CR | PINION BRG, SHIM & BOLTS INCL. | $231.41 | ||||
707338-2X | RING & PINION KIT 3.92 RATIO, 26 SPLINE PINION, CR | FRONT PINION BRG, SHIM & BOLTS INCL. | $281.75 | ||||
707338-3X | RING & PINION KIT 4.09 RATIO, 26 SPLINE PINION, CR | 1994-94 1/2 W2500 FRONT PINION BRG, SHIM & BOLTS IN | $227.93 | ||||
707338-5X | RING & PINION KIT 4.10 (41 - 10) | $261.82 | |||||
707381-3X | RING & PINION KIT 3.55 RATIO, 29 SPLINE PINION, ALS | FRONT PINION BRG, SHIM & BOLTS INCL. | $299.17 | ||||
707381-4X | RING & PINION KIT 3.73 RATIO, 29 SPLINE PINION, ALS | PINION BRG, SHIM & BOLTS INCL. | $302.67 | ||||
74720-5X | RING & PINION SET 4.10 RATIO-THICK, 26 SPLINE PINION | 1997 TJ NON ABS RING & PINION ONLY | $214.37 | ||||
75518-5X | GEAR SET 3.54 | 1989 1/2-90 Corvette | $411.00 | ||||
75861-5X | GEAR SET 3.55 | 1997 TJ NON ABS | $250.00 |
Ring & Pinion Set up tool. Your cost $48.98 + S&H. |
|||
80739-5 | RING & PINION SET 3:07 (43-14) | $264.07 | |||||
85106-5 | GEAR SET W/SM PTS 4:10 (41-10) | $228.56 | |||||
85106-6 | GEAR SET W/SM PTS 4:10 (41-10) | $271.80 | |||||
85609-5 | GEAR SET W/SM PARTS 3.07 (43 - 14) | $318.82 | |||||
85610-5 | GEAR SET W/SM PARTS 3.73 | $359.99 | |||||
BEARING KIT Dana 44
|
|||||||
706032X | BEARING KIT | $28.67 | Note: Ford has installed two types of bearings in the Dana 44IFS, recommend disassembly before ordering. | ||||
DTS28RMK | Bearing/Overhaul Kit Early | $107.87 | |||||
DTRA28LRMK | Bearing/Overhaul Kit Late | $110.20 | |||||
706031X | Inner Pinion Bearing | $17.32 | |||||
706030X | Outer Pinion Bearings | $12.32 | |||||
BCA-A-37 | Carrier Bearing | $22.98 |