Having problems with your General Motors transfer case? 

We offer the widest selection of rebuilt remanufactured transfer cases for General Motor vehicles including the following models: Chevrolet GMC rebuilt transfer case replacements
Acadia, Envoy, Denali, Jimmy, K15/K1500 Pickup, K25/K2500 Pickup, K35/K3500 Pickup, S-15 Jimmy, S-15 Sonoma, Safari, Sevana, 1500, Sevena 2500, Sierra 1500, Sierra 2500, Sierra 3500, Suburban, Syclone, Topkick, Typhoon, V1500 Pickup, V1500 Suburban, V2500 Pickup, V2500 Suburban and Yukon.  Removing and replacing a transfer case with our remanufactured unit is much easier then overhauling the transfer case.  We can provide a direct drop in replacement, removing all risk of getting the incorrect unit. Our transfer cases have a 12 month unlimited mileage no hassel warranty.

 

Rebuilt replacement transfer cases are provided for the following transfer case models:  218AMG, 242AMG, 226GM, BW4481, 246GM, 136GM, BW1372, BW4472, NP233C, NP231C, NP241C, NP205, NP236GM, NP207C, ROCKWELL 221, NP243, NP241, NP208, NP203, BW1370, BW4470, BW4401, NP261XHD and NP263XHD. 

overhaul or replace transfer case

Only New Replacement Parts Used

Purchase any DTS-UMT model transfer case and be assured your transfer case will have the latest compliance upgrades installed!            Not offered by most builders

Our rebuilt transfer cases get new seals, bearings, chains, fork pad, and viscous couplers.  All shafts, slider, hubs and planets are inspect to ensure proper tolerances are maintained. All units are tested at the factory prior to shipment.  Low service expectancy parts are automatically replaced regardless of their condition.   All other parts that do not have absolutely new potential service life are replaced with only the highest quality parts available. Improvements (upgrades) are performed to improve on the manufacturer's design when possible.

But these procedures alone will not guarantee you the highest quality transfer case. It is the experience of the crafts people with their knowledge, dedication and uncompromising desire to improve that makes our remanufactured transfer cases the standard of quality in the industry.  Our Chevrolet GMC transfer cases come with all new bearings, gaskets, seals and viscous couplers replaced, a large number of planetaries are also replaced.  Detailed inspection procedures and each unit is factory pressure tested and comes with a no hassle warranty.  With you assembly number we remove all risk from getting a unit that was not designed for your vehicle.  Encoder motors are available separately.

 

Someone offering to rebuild your existing unit

Someone offering to rebuild your existing unit, wondering what the difference is between rebuilt unit and tcase_id_tag_large.jpgre manufactured unit? The person offering the rebuild service gives you a price typically without opening up your transfer case. He is guessing and betting that he can fix the unit with minimum expense for parts and get you on your way without a warranty!  Re manufactured units have more new parts and come with a 12 month warranty. Another thing to consider is that it takes less mechanical skills to remove and replace a complete unit than it does to rebuild a unit if you are considering doing the job yourself also less time. If you have good mechanical skill and time rebuilding your existing unit is recommended.  Use the figures to the right to assist you in correctly identify what transfer case you have, it's located on the rear of the unit. The assembly number is the key to getting a direct drop in replacement.  Information is also provide to assist you in identify which Yoke and Switch types that your transfer case has.

So the next time you need a rebuilt transfer case remember - all transfer cases are not the same - you can never make a bad decision by choosing the best.     All rebuilt transfer cases get new seals, bearings, chains, fork pad, encoder motors and viscous couplers.  All shafts, slider, hubs and planets are inspect to ensure proper tolerances are maintained. All units are tested at the factory prior to shipment.

bw_id_tag_large.jpg

 
  • Factory Built
  • Parts inspected to OE specifications
  • Computerized Pressure Tested
  • Computerized Spin Tested for Noise and Shift ability
  • All new bearings
  • All new seals
  • New Chain
  • New Viscous Couplers
  • Great Value! 12 month, unlimited miles warranty!
 
 
Extended warranty now available! Extend to two years for additional $200.00. extend to three years for additional $300.00

Wondering what is a core?
 
Please provide the assembly number of the tag on the rear of your New Process transfer case, this will ensure that you receive a direct drop in replacement. What transfer case do you have? Just consult our detailed application guide below!  Having problems shifting your electric transfer case, we offer a complete lline of electronic encoder motors.

 

Replacement parts to assist you with the repair of your Transfer Cases for Chevrolet, Dodge, Ford, GMC, Jeep and many more! Find your transfer case parts.

 

Transfer Case, Remanufactured Transfer Cases, Save Money, select your vehicle model from the following list will take you to the units available for your application.

 

Acadia Sevana 1500 V1500 Pickup    
Envoy Sevena 2500 V1500 Suburban  
Jimmy Sierra 1500 V2500 Pickup    
K15/K1500 Pickup Sierra 2500 V2500 Suburban  
K5/K1500 Suburban Sierra 2500HD Yukon  
K25/K2500 Pickup Sierra 3500  
K5/K1500 Suburban Syclone  
K35/K3500 Pickup Topkick    
S-15 Jimmy Typhoon    
S-15 Sonoma    
Safari    

 Please Clickon Part Number to Buy it online . 

Model Model Year Description Transfer Case Model Number Part Number
Your Cost
Core Deposit
ACADIA 2010-09 AWD - Power Take-Off Unit   DTSUMT150
$879.38
 
$350.00
CANYON 2004-2010  27 spline input, two indicator switches, one rear sensor  w/o speedo hole, square front output yoke, electric shift, need encoder motor order UMM1700   DTSUMT170  $ 1407.00  $350.00
ENVOY 2008 27 spline input, rear slip, male front output, AWD, no external controls 120 GM DTSUMT136-4
$1076.26
$350.00
ENVOY 2008 27 spline input, electric shift, rear slip, male front slip single speed 126GM DTSUMT136-3
$900
$250.00
ENVOY 2008-02 27 spline input, (electric shift) male front slip yoke, if required order encoder motor part number UMM1226 226GM DTSUMT136-2
$895
$350.00
ENVOY 2001-99 27 spline front input, rear slip output male front output spline (electric shift) if required order encoder motor part number UMM1237 236GM DTSUMT136-1
$845
$200.00
ENVOY 2000-98 Ext. Cab 27 spline input, 32 spline slip rear output, electric shift, electronic speedo, slip frontif required order encoder motor part number UMM1233 NP233C DTSUMT108-3More Info
$845
$200.00
ENVOY XL / XUV 2008-02 27 spline input, (electric shift) male front slip yokeif required order encoder motor part number UMM1226 226GM DTSUMT136-2
$895
$350.00
ENVOY XL / XUV 2007-04 27 spline input, electric shift, rear slip, male front slip single speed 126GM DTSUMT136-3
$900
$250.00
JIMMY (Full Size) 2001-98 27 spline front input, rear slip output male front output spline (electric shift ) if required order encoder motor part number UMM1237 236GM DTSUMT136-1
$845
$200.00
JIMMY (Full Size) 1991-90 27 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front output NP241C DTSUMT132
$1045
$200.00
JIMMY (Full Size) 1991-89 32 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front output NP241C DTSUMT133
$1045
$200.00
JIMMY (Full Size) 1991-88 32 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT110 More Info
$1045
$200.00
JIMMY (Full Size) 1989-88 27 spline front input, rear slip output two wire indicator, 2" speed hole 4" square front output yoke NP241C DTSUMT134
$1045
$200.00 
JIMMY (Full Size) 1989-88 32 spline front input, rear slip output two wire indicator, 2" speed hole 4" square front output yoke NP241C DTSUMT130
$1045
$200.00 
K15/K1500 PICKUP 1986-85 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350.00
K15/K1500 PICKUP 1986-85 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1017.19
$350.00
K15/K1500 PICKUP 1986-81 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$981.75
$350.00
K15/K1500 PICKUP 1986-81 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$981.75
$350.00
K15/K1500 PICKUP 1986-69 10 spline external front input,slip rear output yoke,married figure 8 adaptor NP205C DTSUMT507-1
$1017.19
$350.00
K15/K1500 PICKUP 1986-69 27 spline external front input, slip rear output, married figure 8 adaptor NP205C DTSUMT502-1
$1017.19
350.00
K15/K1500 PICKUP 1986-69 27 spline external spline front input, fixed rear output yoke, figure 8 adaptor, married, 10 spline NP205C DTSUMT502-2
$1017.19
350.00
K15/K1500 PICKUP 1981-69 10 external spline front input, fixed front & rear yokes, married, figure 8 adaptor, w/o two side moounts NP205C DTSUMT506-2 $1017.19
$350.00
K15/K1500 PICKUP 1981-69 10 external spline front input, fixed front & rear yokes, married, figure 8 adaptor, with two side mounts NP205C DTSUMT506-1
$1017.19
$350.00
K15/K1500 PICKUP 1979-73 married, full time, chain driven, 27 spline New Process NP203C DTSUMT501-1
Not Availabe
K15/K1500 PICKUP 1979-73 married, full time, chain driven, 32 spline New Process NP203C DTSUMT501-2
Not Availabe
K15/K1500 SUBURBANN 1986-85 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350
K15/K1500 SUBURBANN 1986-85 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1017.19
$350
K1500 PICKUP 1999-96 (electric shift) 27 spline front input, rear slip output three wire indicator, electronic speedo, f if required order encoder motor part number UMM1243 NP243C DTSUMT114-1More Info
$895
$200
K1500 PICKUP 1999-96 (electric shift) 32 spline front input, rear slip output three wire indicator, electronic speedo, f if required order encoder motor part number UMM1242 NP243C DTSUMT114-2More Info
$895
$200
K1500 PICKUP 1999-95 32 spline input, rear slip output two wire terminal fixed front yoke electronic speedo New Process NP241C DTSUMT126-1
$1045
$200
K1500 PICKUP 1999-95 27 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT127
$1045
$200
K1500 PICKUP 1998-95 32 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT128
$1045
$200
K1500 PICKUP 1994 32 spline front input, rear slip output three wire indicator 4" bell front output yoke, 4L80E Trans. NP241C DTSUMT111 More Info
$1045
$200
K1500 PICKUP 1994-93 27 spline front input, rear slip output three wire indicator, electronic speedo, 4" bell front outp NP241C DTSUMT112 More Info
$1045
$200
K1500 PICKUP 1994-89 32 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT110 More Info
$1045
$200
K1500 PICKUP 1992-89 27 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT109 More Info
$1045
$200
K1500 PICKUP 1991-90 27 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front output NP241C DTSUMT132
$1045
$200
K1500 PICKUP 1991-89 32 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front output NP241C DTSUMT133
$1045
$200
K1500 PICKUP 1990-88 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350.00
K1500 PICKUP 1990-88 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1017.19
$350.00
K1500 PICKUP 1989-88 32 spline front input, rear slip output two wire indicator, 2" speed hole 4" square front output yoke NP241C DTSUMT130 $1045
$200
K1500 PICKUP 1988 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$981.75
$350.00
K1500 PICKUP 1988 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
K25/K2500 PICKUP 1986-85 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350.00
K25/K2500 PICKUP 1986-85 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1017.19
$350.00
K25/K2500 PICKUP 1986-81 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
K25/K2500 PICKUP 1986-81 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
K25/K2500 PICKUP 1986-69 10 spline external front input,slip rear output yoke,married figure 8 adaptor NP205C DTSUMT507-1
$1017.19
$350.00
K25/K2500 PICKUP 1986-69 27 spline external front input, slip rear output, married figure 8 adaptor NP205C DTSUMT502-1
$1017.19
$350.00
K25/K2500 PICKUP 1986-69 27 spline external spline front input, fixed rear output yoke, figure 8 adaptor, married, 10 spline NP205C DTSUMT502-2
$1017.19
$350.00
K25/K2500 PICKUP 1981-69 10 external spline front input, fixed front & rear yokes, married, figure 8 adaptor, w/o two side mounts NP205C DTSUMT506-2
$1017.19
$350.00
K25/K2500 PICKUP 1981-69 10 external spline front input, fixed front & rear yokes, married, figure 8 adaptor, with two side mounts NP205C DTSUMT506-1
$1017.19
$350.00
K25/K2500 PICKUP 1979-73 married, full time, chain driven, 27 spline New Process NP203C DTSUMT501-1
Not Availabe
K25/K2500 PICKUP 1979-73 married, full time, chain driven, 32 spline New Process NP203C DTSUMT501-2
Not Availabe
K25/K2500 SUBURBANN 1986-85 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350.00
K25/K2500 SUBURBANN 1986-85 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1017.19
$350.00
K2500 PICKUP 2000-96 (electric shift) 32 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output yoke 4L80E Trans, if required order encoder motor part number UMM1243 NP243C DTSUMT114-2More Info
$895
$200
K2500 PICKUP 2000-95 27 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT127
$1045
$200
K2500 PICKUP 2000-95 32 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT128
$1045
$200
K2500 PICKUP 1999-96 (electric shift) 27 spline front input, rear slip output three wire indicator, electronic speedo, f, if required order encoder motor part number UMM1243 NP243C DTSUMT114-1More Info
$895
$200
K2500 PICKUP 1999-95 32 spline input, rear slip output two wire terminal fixed front yoke electronic speedo New Process NP241C DTSUMT126-1
$1045
$200
K2500 PICKUP 1994 32 spline front input, rear slip output three wire indicator 4" bell front output yoke, 4L80E Trans. NP241C DTSUMT111 More Info
$1045
$200
K2500 PICKUP 1994-93 27 spline front input, rear slip output three wire indicator, electronic speedo, 4" bell front outp NP241C DTSUMT112 More Info
$1045
$200
K2500 PICKUP 1994-89 32 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front outpu NP241C DTSUMT110 More Info
$1045
$200
K2500 PICKUP 1992-89 27 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT109 More Info
$1045
$200
K2500 PICKUP 1991-89 32 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front outpu NP241C DTSUMT133
$1045
$200
K2500 PICKUP 1990-89 27 spline front input, rear slip output two wire indicator, electronic speedo, 4" square front output NP241C DTSUMT132
$1045
$200
K2500 PICKUP 1990-88 Short 32 spline internal front input, rear slip output yoke, married figure 8 adaptor NP205C DTSUMT505-3
$1017.19
$350.00
K2500 PICKUP 1990-88 Short 32 spline internal input, fixed rear output, married figure 8 adaptor NP205C DTSUMT505-4
$1036.88
$350.00
K2500 PICKUP 1989-88 32 spline front input, rear slip output two wire indicator, 2" speed hole 4" square front output yoke NP241C DTSUMT130
$1045
$200
K2500 PICKUP 1988 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
K2500 PICKUP 1988 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
K35/K3500 PICKUP 1986 32 long input (3.500) 32 rear slip, figure 8 adaptor, square front output yoke NP205C DTSUMT505-5
$1036.88
$350.00
K35/K3500 PICKUP 1979-77 married, full time, chain driven, 27 spline New Process NP203C DTSUMT501-1
Not Availabe
K35/K3500 PICKUP 1979-77 married, full time, chain driven, 32 spline New Process NP203C DTSUMT501-2
Not Availabe
K35/K3500 PICKUP 1974-73 married, full time, chain driven, 27 spline New Process NP203C DTSUMT501-1
Not Availabe
K3500 PICKUP 2000-95 32 spline front input, fixed front output yoke, slip rear output yoke, w/P.T.O., 3 position switch BW1370 BW4401 DTSUMT120-1 More Info
$1295
$250
K3500 PICKUP 2000-94 32 spline front and rear fixed yokes, w/P.T.O., 3 position switch Borg Warner BW1370 BW4401 DTSUMT117-1More Info
$1295
$250
K3500 PICKUP 1997-94 32 spline front and rear fixed yokes, w/P.T.O., 3 position switch Borg Warner BW4470 DTSUMT121-1More Info
$1450
$200
K3500 PICKUP 1997-94 32 spline front input shaft, fixed rear output yoke, 4" bell type front output yoke, w/P.T.O., 3 pos switch BW4470 DTSUMT123-1
$1450
$200
K3500 PICKUP 1996-94 32 spline, w/P.T.O. 4" bell front output yoke, fixed rear output yoke 3 position switch Borg Warner BW1370 BW4401 DTSUMT116-1More Info
$1295
$250
K3500 PICKUP 1994 32 spline, w/P.T.O., slip rear yoke, 4" bell front output yoke, 3 position switch Borg Warner BW1370 BW4401 DTSUMT119-1More Info
$1295
$250
K3500 PICKUP 1993 32 spline w/P.T.O. slip rear yoke, 4" bell front output yoke, 2 position switch Borg Warner BW1370 BW4401 DTSUMT118-1More Info
$1295
$250
K3500 PICKUP 1993-89 32 spline front input, w/P.T.O., fixed rear yoke, 4" bell yoke front output, 2 position switch Borg BW1370 BW4401 DTSUMT116-2More Info
$1295
$250
K3500 PICKUP 1992-90 32 spline front input, w/P.T.O. fixed rear yoke, 4" bell front output yoke, 2 position yoke Borg War BW4470 DTSUMT123-2
$1450
$200.00
K3500 PICKUP 1992-89 32 spline w/P.T.O. slip rear yoke, 4" bell front output yoke, 2 position switch Borg Warner BW1370 BW4401 DTSUMT118-1More Info
$1295
$250
K3500 PICKUP 1991-88 32 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT110 More Info
$1045
$200
K3500 PICKUP 1990-85 Long 32 spline internal front input, fixed rear output yoke, round adaptor, married 3.500 input NP205C DTSUMT505-2
$1036.88
$350.00
K3500 PICKUP 1990-85 Long 32 spline internal front input, slip rear output, married round adaptor, 3.500 input NP205C DTSUMT505-1
$1036.88
$350.00
S15 JIMMY 2005-99 27 spline front input, rear slip output male front output spline (electric shift )if required order encoder motor part number UMM1237 236GM DTSUMT136-1
$845
$200
S15 JIMMY 2005-96 Ext. Cab 27 spline input, 32 spline slip rear output, electric shift, electronic speedo, slip front, if required order encoder motor part number UMM1233 NP233C DTSUMT108-3 More Info
$845
$200
S15 JIMMY 1998-95 27 spline front input, 27 spline rear slip output, electric shift, electronic speedo, slip front output,if required order encoder motor part number UMM1233 NP233C DTSUMT108-1
$845
$200
S15 JIMMY 1997-96 Ext. Cab 27 spline front input, 32 spline rear slip yoke, front slip output, electronic speedo, wire NP231C DTSUMT104-3
$895
$200
S15 JIMMY 1997-96 32 spline rear output, 4.90 front input mounting flange Borg Warner, AWD BW1372 BW4472 DTSUMT103 More Info
$995
$200
S15 JIMMY 1997-95 27 spline front input 27 spline slip rear output fixed front yoke, electronic speedo, electric shift, if required order encoder motor part number UMM1233 NP233C DTSUMT107-2
$845
$200
S15 JIMMY 1994 Ext. Cab 27 spline front input, 32 spline rear yoke, front slip yoke, electronic speedo, wire or vacuum shift indicator, top mounting holes, flat seal retainer NP231C DTSUMT104-2
$895
$200
S15 JIMMY 1994-93 32 spline rear output, 4.13 front input mounting flange, 5" front output circular yoke Borg Warner, BW1372 BW4472 DTSUMT102 More Info
$995
$200
S15 JIMMY 1994-92 Ext. Cab 27 spline front input 32 spline rear slip output, electric shift, electronic speedo, fixed, if required order encoder motor part number UMM1233 NP233C DTSUMT107-1
$845
$200
S15 JIMMY 1988-83 27 spline front input fixed front yoke, 27 spline rear slip yoke speed cable hole New Process NP207C DTSUMT129
$895
$200
S15 SONOMA 2005-96 Ext. Cab 27 spline input, 32 spline slip rear output, electric shift, electronic speedo, slip front, if required order encoder motor part number UMM1233 NP233C DTSUMT108-3
$845
$200
S15 SONOMA 1997-96 Ext. Cab 27 spline front input, 32 spline rear slip yoke, front slip output, electronic speedo, wire NP231C DTSUMT104-3
$895
$200
S15 SONOMA 1995-94 Ext. Cab 27 spline front input 32 spline rear slip yoke, slip front output yoke, electronic speedo, NP231C DTSUMT104-4
$895
$200
S15 SONOMA 1995-94 Ext. Cab 27 spline front input 32 spline slip rear output, electric shift, electronic speedo, slip front output yooke vacuum shift indicator above electric shift, flat seal retainer, if required order encoder motor part number UMM1233 NP233C DTSUMT108-2More Info
$845
$200
S15 SONOMA 1995-94 Ext. Cab 27 spline front input, 32 spline rear yoke, front slip yoke, electronic speedo, wire or vacuum shift indicator, top mounting holes, flat seal retainer NP231C DTSUMT104-2
$895
$200
S15 SONOMA 1994-93 27 spline front input, 27 rear slip output, front slip output, speed sensor, top mounting holes flat seal retainer NP231C DTSUMT104-5
$895
$200
S15 SONOMA 1994-92 Ext. Cab 27 spline front input 32 spline rear slip output, electric shift, electronic speedo, fixed, if required order encoder motor part number UMM1233 NP233C DTSUMT107-1
$845
$200
S15 SONOMA 1994-92 Ext. Cab 27 spline front input 32 spline rear slip output, electric shift, electronic speedo, fixed, if required order encoder motor part number UMM1233 NP233C DTSUMT107-3
$845
$200
S15 SONOMA 1993-92 Ext. Cab 27 spline front input 32 spline rear slip output, fixed front yoke, wire or vacuum shift indicator NP231C DTSUMT106-1More Info
$895
$200
S15 SONOMA 1993-92 Ext. Cab 27 spline front input 32 spline rear slip output, fixed front yoke, wire or vacuum shift indicator NP231C DTSUMT106-2
$895
$200
SAFARI 2005-99 27 spline front input, rear slip output male front output spline (electric shift), if required order encoder motor part number UMM1235 136GM DTSUMT135
$200
$350.00
SAFARI 1998-96 27 spline rear output, 4.90 front input mounting flange Borg Warner, AWD BW1372 BW4472 DTSUMT101 More Info
$995
 
$200
SAFARI 1995-90 27 spline rear output 4.13 front input mounting flange 4 1/2" front output circular yoke Borg Warner BW1372 BW4472 DTSUMT100 More Info
$995
 
$200
SAVANA 1500 2008-03 27 spline input, rear slip output, female spline front output A.W.D. BW4473 DTSUMT103-2 More Info
$1115.63
$350.00
SAVANA 2500 2008-03 27 spline input, rear slip output, female spline front output A.W.D. BW4473 DTSUMT103-2More Info
$1115.63
$400.00
 SIERRA 2010-2011 11 mounting studs, 29 spline input, 31 spline rear slip,      32 female spline front output, 1 sensor hole, electric shift, need encoder order UMM1612 1626XHD DTSUMT141-10 $1550  $350
SIERRA 1500 (Include Denali)s DENALI) 2009-08 32 spline input, 32 rear slip female spline front output, manual shift MP1222LD DTSUMT141-8
$1295
 
$350
SIERRA 1500 (Include Denali)s DENALI) 2009-07 27 spline input, 32 rear slip female spline front output (manual shift) MP1222LD DTSUMT141-2
$1295
$350
SIERRA 1500 (Include Denali)s DENALI) 2009-07 27 spline input, 32 rear slip output female spline front output (electric shift )if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-1
$1295
$300
SIERRA 1500 (Include Denali)s DENALI) 2009-07 32 spline input, 32 rear output, female front output shaft (Electric Shift), if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-7
$1295
 
$300
SIERRA 1500 (Include Denali)s DENALI) 2008-07 32 spline input, 32 rear slip, female front output, AWD BW4485 DTSUMT142
$1145
$300
SIERRA 1500 (Include Denali)s DENALI) 2007-03 27 spline input shaft, rear slip output, female front output, splined shift sector, if required order encoder motor part number UMM2237 246GM DTSUMT137-4
$995
$250
SIERRA 1500 (Include Denali)s DENALI) 2007-03 32 spline input shaft, rear slip output, female front output, splined shift sector, if required order encoder motor part number UMM2237 246GM DTSUMT137-5
$995
$250
SIERRA 1500 (Include Denali)s DENALI) 2007-01 27 spline front input, rear slip female front output, AWD 149GM DTSUMT137-3
$1099.88
$350.00
SIERRA 1500 (Include Denali)s DENALI) 2006-99 27 spline front input, 32 rear slip output, female spline front output (manual shift) LD 261GM DTSUMT138-1
$1095
$250
SIERRA 1500 (Include Denali)s DENALI) 2006-99 32 spline front input, rear slip output, female spline front output (manual shift) LD 261GM DTSUMT138-2
$1095
$250
SIERRA 1500 (Include Denali)s DENALI) 2005-03 (electric shift) 27 spline front input, rear slip output, female spline front output, full-time two, if required order encoder motor part number UMM4482 BW4482 DTSUMT140
$1145
$350.00
SIERRA 1500 (Include Denali)s DENALI) 2002-99 (electric shift) 27 spline front input, rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-1
$995
$250
SIERRA 1500 (Include Denali)s DENALI) 2002-99 (electric shift) 32 spline front input rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-2
$995
$250
SIERRA 2500 2004-03 32 spline input (electric shift) 32 spline rear output, female front output shaft, if required order encoder motor part number UMM2263 263HD DTSUMT139-5
$1300
$300
SIERRA 2500 2004-03 29 spline front input, (electric shift) 31 spline rear slip 1.608 O.D. female front output shaft, if required order encoder motor part number UMM2263 263XHD DTSUMT139-3
$1300
$300
SIERRA 2500 2004-03 32 spline input shaft, rear slip output, female front output, splined shift sector, if required order encoder motor part number UMM2237 246GM DTSUMT137-5
$995
$250
SIERRA 2500 2004-01 29 spline front input (manual shaft) 31 spline rear slip 1.608 O.D. female front output shaft 261XHD DTSUMT139-4
$1250
$350
SIERRA 2500 2002-01 32 spline input (electric shift) 32 spline rear output, female front output shaft, if required order encoder motor part number UMM1263 263HD DTSUMT139-5
$1300
$300
SIERRA 2500 2002-01 29 spline front input, (electric shift) 31 spline rear slip 1.608 O.D. female front output shaft, if required order encoder motor part number UMM1263 263XHD DTSUMT139-3
$1300
$300
SIERRA 2500 2002-99 (electric shift) 27 spline front input, rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-1
$995
$250
SIERRA 2500 2002-99 (electric shift) 32 spline front input rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-2
$995
$250
SIERRA 2500 HD 2009-08 29 spline input, 31 rear female spline, front output (Electric shift) if required order encoder motor part number UMM1626 MP1626HD DTSUMT141-9
$1550
 
$350
SIERRA 2500 HD 2009-07 29 spline input, 31 rear slip, female spline front output, manual shift 1226XHD DTSUMT141-4
$1410.96
$400.00
SIERRA 2500 HD 2009-07 29 spline input, 31 rear slip, female spline front output (Electric shift) if required order encoder motor part number UMM3023 MP1625HD DTSUMT141-5
$1450
$350
SIERRA 2500 HD 2009-07 (electric shift) 29 spline input gear, 31 rear slip, female spline front output yoke, if required order encoder motor part number UMM1626 MP1626XHD DTSUMT141-6
$1550
$350
SIERRA 2500 HD 2009-07 32 spline input, 32 rear output, female front output shaft (Electric Shift) if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-7
$1295
 
$300
SIERRA 2500 HD 2006-03 32 spline input (electric shift) 32 spline rear output, female front output shaft, if required order encoder motor part number UMM2263 263HD DTSUMT139-5
$1300
$300
SIERRA 2500 HD 2006-03 29 spline front input, (electric shift) 31 spline rear slip 1.608 O.D. female front output shaft, if required order encoder motor part number UMM2263 263XHD DTSUMT139-3
$1300
$300
SIERRA 2500 HD 2006-01 29 spline front input (manual shaft) 31 spline rear slip 1.608 O.D. female front output shaft 261XHD DTSUMT139-4
$1250
$350.00
SIERRA 2500 HD 2005-01 32 spline front input, 32 rear slip output, female spline front output (manual shift) HD 261GM DTSUMT139-1
$1095
$250.00
SIERRA 3500, 3500 HDD 2009-07 29 spline input, 31 rear slip, female spline front output, manual shift 1226XHD DTSUMT141-4
$1410.94
$400.00
SIERRA 3500, 3500 HDD 2009-07 (electric shift) 29 spline input gear, 31 rear slip, female spline front output yoke, if required order encoder motor part number UMM1626 MP1626XHD DTSUMT141-6
$1550
$350.00
SIERRA 3500, 3500 HDD 2008-07 29 spline input, 31 rear slip, female spline front output (Electric shift) if required order encoder motor part number UMM3023 MP1625HD DTSUMT141-5
$1450
$350.00
SIERRA 3500, 3500 HDD 2006-03 32 spline input (electric shift) 32 spline rear output, female front output shaft, if required order encoder motor part number UMM2263 263HD DTSUMT139-5
$1300
$300.00
SIERRA 3500, 3500 HDD 2006-03 29 spline front input, (electric shift) 31 spline rear slip 1.608 O.D. female front output shaft, if required order encoder motor part number UMM2263 263XHD DTSUMT139-3
$1300
$300.00
SIERRA 3500, 3500 HDD 2006-01 32 spline front input, 32 rear slip output, female spline front output (manual shift) HD 261GM DTSUMT139-1
$1095
$250.00
SIERRA 3500, 3500 HDD 2006-01 29 spline front input (manual shaft) 31 spline rear slip 1.608 O.D. female front output shaft 261XHD DTSUMT139-4
$1250
$3500.00
SIERRA 3500, 3500 HDD 2002-01 32 spline input (electric shift) 32 spline rear output, female front output shaft, if required order encoder motor part number UMM1263 263HD DTSUMT139-5
$1300
$300.00
SIERRA 3500, 3500 HDD 2002-01 29 spline front input, (electric shift) 31 spline rear slip 1.608 O.D. female front output shaft, if required order encoder motor part number UMM1263 263XHD DTSUMT139-3
$1300
$300.00
SYCLONE 1991 27 spline rear output 4.13 front input mounting flange 4 1/2" front output circular yoke Borg Warner BW1372 BW4472 DTSUMT100 More Info
$995
$200
TOPKICK Medium Truckuck) 2007-06 (electric shift) Direct Mount with 3 Flanged Yokes, w/o Speedo Hole,if required order encoder motor part number UMM2263 273C DTSUMT139-6
$1500
$350.00
TYPHOON 1993-92 27 spline rear output 4.13 front input mounting flange 4 1/2" front output circular yoke Borg Warner BW1372 BW4472 DTSUMT100 More Info
$995
$200
V1500 PICKUP 1987 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
V1500 PICKUP 1987 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
V1500 SUBURBAN 1988-87 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
V1500 SUBURBAN 1988-87 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
V2500 PICKUP 1987 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
V2500 PICKUP 1987 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
V2500 SUBURBAN 1988-87 Synchronized front 27 spline input shaft 350-700 Series Trans. New Process NP208C DTSUMT503
$1145
$200
V2500 SUBURBAN 1988-87 Synchronized front 32 spl. input shaft 400 Series Trans. Manual Transmission New Process NP208C DTSUMT504
$1145
$200
YUKON 2009-08 27 spline input, 32 rear slip output female spline front output (electric shift), if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-1
$1295
$300
YUKON 2009-08 32 spline input, 32 rear output, female front output shaft (Electric Shift), if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-7
$1295
 
$300
YUKON 2007-03 27 spline input shaft, rear slip output, female front output, splined shift sector, if required order encoder motor part number UMM2237 246GM DTSUMT137-4
$995
$250.00
YUKON 2005-03 (electric shift) 27 spline front input, rear slip output, female spline front output, full-time two BW4482 DTSUMT140
$1145
$350.00
YUKON 2004-01 27 spline front input, rear slip female front output, AWD 149GM DTSUMT137-3
$1099.88
$350.00
YUKON 2002-99 (electric shift) 27 spline front input, rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-1
$995
$250
YUKON 1999-96 (electric shift) 27 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output yoke 4L60E transmission, if required order encoder motor part number UMM1243 NP243C DTSUMT114-1More Info
$895
$200
YUKON 1999-96 (electric shift) 32 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output yoke 4L80E transmissio, if required order encoder motor part number UMM1243 NP243C DTSUMT114-2More Info
$895
$200
YUKON 1998-95 27 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT127
$1045
$200
YUKON 1996-95 32 spline front input, rear slip output three wire indicator, electronic speedo, fixed front output NP241C DTSUMT128
$1045
$200
YUKON 1994 32 spline front input, rear slip output three wire indicator 4" bell front output yoke, 4L80E Trans. NP241C DTSUMT111 More Info
$1045
$200
YUKON 1994-93 27 spline front input, rear slip output three wire indicator, electronic speedo, 4" bell front outp NP241C DTSUMT112 More Info
$1045
$200
YUKON 1994-92 32 spline front input, rear slip output, two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT110 More Info
$1045
$200.00
YUKON 1993-92 27 spline front input, rear slip output two wire indicator, electronic speedo, 4" bell front output NP241C DTSUMT109 More Info
$1045
$200.00
YUKON DENALI 2009-07 32 spline input, 32 rear slip, female front output, AWD BW4485 DTSUMT142
$1145
$300.00
YUKON DENALI 2006-05 27 spline front input, 32 rear slip, female front output, AWD BW4481 DTSUMT103-3More Info
$1145
$250.00
YUKON DENALI 2006-01 27 spline front input, rear slip female front output, AWD 149GM DTSUMT137-3
$1295
$350.00
YUKON DENALI 2000 (electric shift) 27 spline front input, rear slip output female spline front output, if required order encoder motor part number UMM1237 246GM DTSUMT137-1
$995
$250.00
YUKON XL 1500 2009-08 27 spline input, 32 rear slip output female spline front output (electric shift), if required order encoder motor part number UMM3023 MP3023LD DTSUMT141-1
$1295
$300.00
YUKON XL 1500 2008-07 32 spline input, 32 rear slip, female front output, AWD BW4485 DTSUMT142
$1145
$300.00
YUKON XL 1500 2007-03 27 spline input shaft, rear slip output, female front output, splined shift sector, if required order encoder motor part number UMM2237 246GM DTSUMT137-4
$995
$250.00
YUKON XL 1500 2006-03 27 spline front input, 32 rear slip, female front output, AWD BW4481 DTSUMT103-3More Info
$1145
$250.00

 

 

 

 

Replacement Upgrade replace your 136GM full time transfer case with our modified NP231 you will now part time all-wheel-drive with low range, modifications will a different front output shaft , you supply linkage. Your cost on this unit is $905.00 plus $250.00 core deposit plus the freight.

 
 

The following charges may be deducted from your core deposit if you have:

$234.00 Damaged Case

$100.00 Cut wire on coil

$ 40.00 Missing Yoke (front or rear)

$ 40.00 Missing extension housing.

Use the following figures to identify Yoke and Switch types.

 
 
 

 

transfer1.jpeg

 

 

transfer4.jpeg

transfer2.jpeg  

transfer5.jpeg   

transfer3.jpeg
 

transfer6.jpeg

 

Transfer Case Assemblies are delivered with 12 month unlimited mile warranty, from time of purchase. When ordering please provide vehicle make, year, model,, transfer case model number and assembly numbers off existing transfer case tag, this information will ensure that you receive a direct drop in replacement.
 

The core deposit will be refunded for assembled transfer case cores only. The core charge is a deposit placed on you credit card to ensure that you return your original transfer case, when received we send you a check the core deposit amount less return freight if returned COD (please call to make this arrangement). Prices subject to change without notice.

 

Transfer Case Motors Sold Separately

 

These are high quality remanufactured units, a $48.00 core charge will apply until you return your old unit. Cores must be returned with-in 30 days. Purchase one of these encoder motors at the same time as transfer case and take a 10% discount on the encoder motor!

 

 

UMM1226    
$217.50
UMM1233    
$162.75
UMM1235    
$162.75
UMM1237    
$168.38
UMM1243    
$168.45
UMM1263    
$264.75
UMM1626    
$368.25
UMM1700      $293.36
UMM2237    
$357.75
UMM2263    
$330.75
UMM3023    
$498.75
UMM4482    
$265.13

 

 

 

 
 

 

Information is available to assist you in trouble shooting your GM encorder motor in your vehicle. 

Extended warranty is available to be purchased at time of original purchase. Warranty covers material and workmanship including parts and labor at the factory. The warranty will not apply to units damaged, broken cases, units run low or without fluid and damage caused by accident. This warranty is applicable to units returned to the factory for inspection and repair. This warranty does not cover freight or labor to remove or replace the transfer case.